Register



Pages: [1]

Series 2A MOT

· 10 · 2247
« previous next »

0 Members and 2 Guests are viewing this topic.

*

dalbuie

  • *****
  • Posts: 102
  • Name: David Black
Series 2A MOT
« on: November 28, 2013, 02:10:55 PM »
Hi,

My Series 2A goes in for its MOT tomorrow and I've heard mentioned that the brakes shouldn't be tested on single axle rollers (it doesn't have free wheeling hubs). The MOT station I go to does all my old cars and they are sympathetic to classics - but I wondered if there are any issues in brake testing (other than the handbrake that can't be put on while moving). I'm not sure if any damage could be caused if it was in 2 wheel drive mode and neutral. Some people have even mentioned removing the front prop.

Any advise?

Thanks
D
Logged
Never look into a laser with your remaining eye!
*

ffourphantomfixer

  • *****
  • Posts: 506
  • Name: Andrew Forrest
Re: Series 2A MOT
« Reply #1 on: November 28, 2013, 03:07:54 PM »
Providing it is NOT in 4 wheel drive (rear wheels only) then it can be tested normally. 

The hand brake can be tested on the rollers but not violently.

Or the garage can use an accelerometer on the floor (if they have one) and test the brakes whilst driving.
Logged
She said at my age I need something else to play with
*

dalbuie

  • *****
  • Posts: 102
  • Name: David Black
Re: Series 2A MOT
« Reply #2 on: November 28, 2013, 04:49:19 PM »
Many thanks, I feel a bit better about it now.

Logged
Never look into a laser with your remaining eye!
*

lurch032003

Re: Series 2A MOT
« Reply #3 on: November 28, 2013, 09:51:45 PM »
I had my s3 done this year which also involved a road test which it failed on as when braked it would pull to one side which found prob and fixed easy enough but again on retest it was a road test then the rolling road to check rear and handbrake which it passed well on .
Logged
*

lurch032003

Re: Series 2A MOT
« Reply #4 on: November 28, 2013, 09:52:30 PM »
Oh and it was on two wheel drive with no free wheeling hubs fitted
Logged
*

Dunc

  • *****
  • Posts: 181
  • Name: Duncan Thomson
Re: Series 2A MOT
« Reply #5 on: November 29, 2013, 07:53:35 PM »
  Any news yet !! 
Logged
If a hammer won't fix it, get a bigger hammer !!
*

dalbuie

  • *****
  • Posts: 102
  • Name: David Black
Re: Series 2A MOT
« Reply #6 on: November 30, 2013, 02:39:33 PM »
A PASS :-)

Borderline on front brakes due to a binding on passenger side (mechanical bind that only appears when wheel tightened up and thought I had fixed it) but I have time to play about with it now.

Cheers

Logged
Never look into a laser with your remaining eye!
*

genem

  • *****
  • Posts: 2140
  • I'm not completely daft. Some pieces are missing.
  • Name: Gene Maxwell
Re: Series 2A MOT
« Reply #7 on: November 30, 2013, 03:00:42 PM »
^^^^^ Check the width of the shoes. I've seen reports of pattern parts that were wider than original spec, enough to foul the drum when its torqued up.
Logged
If its not broken you are not trying hard enough....
*

lurch032003

Re: Series 2A MOT
« Reply #8 on: November 30, 2013, 04:50:48 PM »
File down the outer edge by a 1/16inch and tighten up drum without wheel on and see if its catching if so again 1/16 till its free then adjust the brakes remeber to do the Chaffee on both ends glad you passed bet that's a load of your mind for winter also.  :-) :-) :-)
Logged
*

dalbuie

  • *****
  • Posts: 102
  • Name: David Black
Re: Series 2A MOT
« Reply #9 on: November 30, 2013, 07:24:51 PM »
Thanks, yes happy now. Will try the 1/16" idea.

Also there is some 'play' on the bottom banjo ring on this side - none on the other - so wondered how tight this should be.
Logged
Never look into a laser with your remaining eye!
Pages: [1]
« previous next »