SLROC Forum
General Category => GENERAL CHAT => Topic started by: Buffalo Bill on April 15, 2012, 08:34:31 PM
-
as above (http://i1099.photobucket.com/albums/g392/billconner1/P4150341.jpg)
not good lol
ok changed the title as it no longer has any rust.
Big thanks to the nice man with a set of axles. and the man with doors and the man with a seat box, oh yes and the man with the cappings
And to my helpers Wee Billy(not so wee), George who is now smitten with landies and finaly Scott.
-
after a few hours work it looks a little better
(http://i1099.photobucket.com/albums/g392/billconner1/P4150343.jpg)
-
Where? I don't see it :P
-
its round the bottom of the shock :o
-
thats a nice looking repair
dave
-
Will it be ready for our next RTV!?! ;)
-
oh yes. But i think i will need a test pilot ;) ;)
lol
-
jesus Bill, that made mine look solid! Start saving now.
-
what is the current rules on patch sizes for the mot, there used to be rules about how much origonal metal is left. or did that go out when they brought in the seam welded rule?
-
as far as i know you can only replace 40% with patches so i should be just inside that lol
-
found a gremlin
(http://i1099.photobucket.com/albums/g392/billconner1/P4140330.jpg)
and it got worse!!"!
(http://i1099.photobucket.com/albums/g392/billconner1/P4140336.jpg)
i may take out shares in welding wire lol
-
as far as i know you can only replace 40% with patches so i should be just inside that lol
not any more :o :o
-
looking a little better should be finished next weekend, thats if my welder holds out!!
(http://i1099.photobucket.com/albums/g392/billconner1/P4220017.jpg)
done the inside as well
(http://i1099.photobucket.com/albums/g392/billconner1/P4220019.jpg)
and found more rott!!
(http://i1099.photobucket.com/albums/g392/billconner1/P4220016.jpg)
just waiting on some parts should finish the welding this weekend.
:D
-
Looking good Bill, but what's the rest like. Everywhere I looked on mine, I only had to touch it and a hole appeared.
-
yea will probably have pretty much done the same to drivers side althogh its not as bad. im using 4mm plate hard to work with but should get a good few years out of it.
Cheers Bill
-
And now for the other side >:(
(http://i1099.photobucket.com/albums/g392/billconner1/P4260002.jpg)
this weather is not helping >:(
-
A little more done today. Until i ran out of co2!!
(http://i1099.photobucket.com/albums/g392/billconner1/P4290003.jpg)
(http://i1099.photobucket.com/albums/g392/billconner1/P4290004.jpg)
Getting there.
-
Ok new bottle of co2 so off again
(http://i1099.photobucket.com/albums/g392/billconner1/P5010001.jpg)
(http://i1099.photobucket.com/albums/g392/billconner1/P5010002.jpg)
(http://i1099.photobucket.com/albums/g392/billconner1/P5010003.jpg)
and i actualy managed to save an original bit!!!
(http://i1099.photobucket.com/albums/g392/billconner1/P5010004.jpg)
hard to believe but the welding is all done apart from a spring hanger.
-
Bill,
If you had done the Titanic it would still be afloat ;) ;)
-
.... or sunk when it launched if he used plate that thick :o :o
-
Waxoyl the chasis then the MOT man will never see how
much little is original
-
was starting to look the part
(http://i1099.photobucket.com/albums/g392/billconner1/P5040001.jpg)
(http://i1099.photobucket.com/albums/g392/billconner1/P5040002.jpg)
then i found this so the welder is out yet again!!!!
(http://i1099.photobucket.com/albums/g392/billconner1/P5040005.jpg)
she is looking a bit sorry for her self
(http://i1099.photobucket.com/albums/g392/billconner1/P5040006.jpg)
but i can see the finish line in sight.
-
ok another day another weld
(http://i1099.photobucket.com/albums/g392/billconner1/P5050002.jpg)
(http://i1099.photobucket.com/albums/g392/billconner1/P5050004.jpg)
i know landies are bad for rust but this is rediculas!!!!!!! :'(
now have to build a fuel tank bracket the fun never ends!!!
-
And I thought mine was bad!!!
-
been a bit quiet with this as i had a bit of a miss hap!!!!
should be back on track this weekend.
The guys i have to collect stuff from hopefully this weekend.
thanks for your patience ...Bill
-
think i may have over done the lift kit!!!!!!
(http://i1099.photobucket.com/albums/g392/billconner1/P5260006.jpg)
(http://i1099.photobucket.com/albums/g392/billconner1/P5260007.jpg)
(http://i1099.photobucket.com/albums/g392/billconner1/P5260005.jpg)
looks good but would be a handful on side slopes!!!!
-
some progress made today!
(http://i1099.photobucket.com/albums/g392/billconner1/P6020010.jpg)
well roofs on brakes are done fuel tank is back in all is going surprisingly well.
-
Looking good Bill.
-
That's coming along nicely 8)
-
ok guys as scary as this is its going for its mot on wednesday, fingers and pretty much everything else crossed.
(http://i1099.photobucket.com/albums/g392/billconner1/P6160013.jpg)
(http://i1099.photobucket.com/albums/g392/billconner1/P6160014.jpg)
hope fully be out and about in it next month
-
looking good hope all goes well with the MOT
dave
-
mmm -suspicially fresh Bill
Could do with streamlining the winch bumper though Might get the mpg of a diesel instead of a V8
Seriously it's good looking and with the welding you did it should last a long time
Duncan
-
Looks good, should cruise the mot. :)
-
yea its turned out realy well guys
big thanks to
wee or ok not so wee Billy, George, Scott, Kerion, Duncan, and my darling wife Sheona who paints all my motors.
this has been fun for all involved and hopefully the mot will go well.
thanks again Bill
-
Good luck Bill!
-
All fingers crossed - good luck with this one eh !
G.
-
Well, Bill. We're waiting with bated breath! Did she pass???
-
Sorry guys currently in Mallorca. The wrong timing belt was supplied all sorted now but mot won't be till Wednesday of next week. I will post as soon as it pass/fails ::)
Thanks bill
-
Sorry guys currently in Mallorca. The wrong timing belt was supplied all sorted now but mot won't be till Wednesday of next week. I will post as soon as it pass/fails ::)
Thanks bill
wow, you're working on it in Mallorca, that's dedication. Explains the large suitcase, does your wife know :)
-
Not yet shhh ::) how is yours do you have the snorkel on yet ??
-
Not yet, hit a small problem. My retro look wing mirrors are in the way and I don't want to take them off. Awaiting my neighbour to provide a solution :)
-
ok 90 went for mot at 10 failed on hazard warning switch resat at 11 and passed. The MOT guy was quite impressed.
hope ive kept you all entertained for a bit and hope to see you at events soon.
thanks for watching Bill ;D
-
Congratulations Bill, Well Done. That was a huge effort - Don't break this one !
G.
-
well done all that hard work paid off
dave
-
took it to get muddy today lots of fun and no misshaps.
probably because my son drove most of the day. ;D
-
Ok guys she passed mot with no problems in June . I have bought yet another barn find must be a glutton for punishment.
I will post pics of the new one soon
Cheers Bill
-
Can't believe this old girl is still on the go. Stronger than ever.